Se Habla EspaƱol - Financing Available - Call for more information
888-437-5438

Cart:

0 item(s) - $0.00
You have no items in your shopping cart.

0

BendPak HDS-35X Extended-Length 4 Post Truck Lift

Double click on above image to view full picture

More Views

 

BendPak HDS-35X Extended-Length 4 Post Truck Lift

Free Shipping

SKU: 119882

$18,680.00
Financing Available!

Quick Overview

The BendPak HDS-35X 4 post truck lift is ideal for semi tractors with extended trailers. Whether your service techs specialize in maintaining Ford F-650 flatbed trucks or concrete transport trucks with 6x4 drivetrains, the extended length of the HDS-35X truck lift will give your techs the capacity to do it. The HDS-35X can hold towing engines with accompanied landing gear up to 29.75 feet in length and almost 13 feet in width.


Unmatched in quality and unparalleled in safety, BendPak’s 4 post car lifts are top-of-the-line. Trust BendPak to lift your heavy-duty tractor units and fixed-chassis cargo trucks that weigh up to 35,000 lbs.


If you need a couple extra thousand pounds of weightlifting capacity, check out the BendPak HDS-40 or BendPak HDS-40X extended length 4 post truck lifts. 

35,000-lb. Capacity Extended-Length Four-Post Truck Lift

OR

OR

Product Description

BendPak's HDS-Truck Series four-post lifts are a whole new breed of rugged. They're newly engineered super-duty truck lifts that make light work out of heavy lifting. They work better, are built to last, and feature upgrades that increase safety, durability and productivity. Four models provide a generous 35,000 or 40,000-lb. lifting capacity and feature extra-wide runways to accommodate a wide variety of vehicle configurations.

Looking for even more lifting capabilities? Check out the 40,000-lb. capacity HDS-40 or the extended 40,000-lb. capacity HDS-40X.

All HDS-35X extended length truck lifts feature:
  • Spring-loaded safety locks automatically engage continuously during rise and adjustable safety ladders allow for precise runway leveling even when installed on sloped floors.
    • Supersized 12” diameter cable sheaves within the runway and cross tubes combined with massive 4” diameter sheave axles dramatically improve cable wear and critical component lifespan meaning you’ll increase safety and spend less money in service related expenses down the road.

    • BendPak's HDS-Truck Series lifts feature four stainless-steel lifting cables that provide a great balance between abrasion resistance and fatigue.

    • Grease nipples are located on every sheave and sheave axle to make lubrication maintenance a breeze.

    • Each HDS-Truck Series four-post lift is equipped with a single hydraulic cylinder hidden away under the runway for maximum performance and reliability and minimum exposure to elements. The hydraulic cylinder features high-durometer rod seals, pressure loaded U-cup piston seals, backups and wear bands that virtually eliminate any fluid bypass. The welded cylinder body is made from high strength steel tubing produced to exceed ASTM specifications. This combination of superb base material and superior processing ensures straight, smooth, cylinders that will provide years and years of dependable trouble-free service.Leak proof cylinder technology only available for BendPak four-post lifts

    • An integrated hydraulic flow restrictor provides a controlled descent in the unlikely event of an unexpected hose rupture.

    • A durable powder coat finish can withstand harsh environments and chemical spills and will provide years of protection.

    • A simple push-button pneumatic lock release makes lowering operations simple and fast. Aircraft-quality stainless steel and aluminum pneumatic cylinders will provide years of trouble-free service.

    • A secondary lock system is on constant guard and acts as a slack-cable device in the unlikely event of an unexpected cable failure.

    • Lifting cables, airlines, safety latches and sheaves are all fully enclosed within lift structure.

    • Features multiple adjustable height locking positions for variable-height parking and infinite leveling.

    • A maintenance-free electric hydraulic power system assures ultimate dependability.

    • All operator controls are conveniently located within easy reach.

    • 12" x 12" base plates provide a solid foundation.

  • Non-skid runways provides maximum grip, even when the runway surface is wet or oily.
  • Optional rolling jacks make a great addition to increase service capacity. Rolling jacks are used to raise the front or rear portion of a vehicle off the runways allowing operators to perform efficient wheel and break service. A pair of jacks allows the entire vehicle to elevated. Each jack has telescoping arms and frame contact pads that can be extended over the runways and positioned under vehicle lifting points. Each jack features three safety-lock positions and stackable truck and van adapters for increased lifting height and better access to frame contact points on high ground-clearance vehicles. The jacks come equipped with a commercial grade air-hydraulic pump.
*Not all BendPak lift models meet the standards as prescribed by ANSI/ALI ALCTV-2006 or ANSI/UL 201. Consult www.autolift.org for a complete list or contact BendPak via contact@bendpak.com.

Product Features

  • 35,000-lb. lifting capacity
  • CE Approved and Certified. Meets or exceeds the standards prescribed by European Standard EN 1493
  • Extended length runways
  • Supersized 12" diameter cable sheaves
  • Stainless steal lifting cables
  • Grease nipples
  • Single hydraulic under-runway cylinder
  • Integrated flow restrictor
  • Durable powder coat
  • Spring-loaded safety locks
  • Second lock system on constant guard
  • Fully enclosed lifting cables
  • Multiple adjustable height locking positions
  • Maintenance-free electric hydraulic power system
  • Conveniently positioned operator controls
  • 12" x 12" base plates
  • Non-skid runways
  • Optional rolling jacks

Technical Specs

  • Lifting capacity*: 35,000 lbs. / 12,247 kg
    • *Max capacity / front axle: 17,500 lbs. / 7,938 kg
    • *Max capacity / rear axle: 17,500 lbs. / 7,938 kg
  • Overall width: 154" / 3,912 mm
  • Outside length: 317" / 8,052 mm
  • Overall length: 357" / 9,068 mm
  • Height of columns: 93" / 2,362 mm
  • Runway min height: 8-1/2" / 216 mm
  • Max rise: 60" / 1,524 mm
  • Max lifting height: 68-1/2" / 1,740 mm
  • Width between posts: 134" / 3,404 mm
  • Runway width: 28" / 711 mm
  • Width between runways: 36" – 47" / 914 mm – 1,194 mm
  • Runway centerline: 64" - 75" / 1,625 mm to 1,905 mm
  • Outside edge of runways: 92" - 103" / 2,367 mm - 2,616 mm
  • Drive-thru clearance: 109" / 2,769 mm
  • Length of runways: 323" / 5,842 mm
  • Min wheelbase @ rated capacity: 230" / 5,842 mm
  • Min wheelbase @ 75% capacity: 195" / 4,953 mm
  • Min wheelbase @ 50% capacity: 165" / 4,191 mm
  • Min wheelbase @ 25% capacity: 130" / 3,302 mm
  • Locking positions: 9
  • Lock spacing: every 6" / 152 mm
  • Lifting time: 75 sec
  • Motor: 220 VAC / 60 Hz / 1 Ph

Note: An air supply (minimum: 30 psi / 3 CFM) is required for the safety-lock mechanisms to disengage. It is solely the responsibility of the end-user to provide, install and maintain the air supply.

*Not all BendPak lift models meet the standards as prescribed by ANSI/ALI ALCTV-2006 or ANSI/UL 201. Consult www.autolift.org for a complete list or contact BendPak via contact@bendpak.com.

You may also be interested in the following product(s)